Verizon also offers analog service, or POTS, over FiOS. The common model optical network terminal has 4 analog phone jacks. Verizon does not do anything that would affect or disable the pre-existing copper lines that carried phone service or DSL, though the official company policy is that customers cannot retreat back to copper service without higher level management approval. However, there have in fact been reports in various markets that Verizon has physically deinstalled the copper lines at the time that FiOS was installed, effectively removing any "path of retreat" to copper based services. Verizon is required by law to share copper media with competing service providers, but no such requirement exists for fiber media. Verizon states that the transport method of providing local service is a corporate decision and they are committed to fiber optic transport. The pricing of POTS over FiOS is identical to POTS over traditional copper. No differences exist as far as billing methods are concerned, as only the delivery system changes. The same packages, rates, deals and telephone taxes exist on FiOS POTS and copper wire POTS. The phone pricing on traditional copper will migrate to FiOS phone when FiOS is installed.
While FiOS phone service offers digital audio quality compared to standard copper phone lines, power outages may affect service availability. Unlike standard phone lines, the FiOS service depends on power at the customer premises. The FiOS backup battery will power the phone lines for 4 to 8 hours of call time (reports vary). This may be an issue for sites that experience extended power outages that depend on analog phone lines for remote monitoring, alarm systems, and/or emergency calls. Verizon claims that the video and Internet streams are disabled during outages to conserve power for emergency dial tone use, but many FiOS users have observed that the Internet stream is still operational when power is removed.

Internet access

There are several tiers of residential Internet service. Availability depends upon the location of the customer; in areas of intense competition, speeds are higher.
Available speed tiers, in megabits per second Mbps
Common Speeds
  • 5 Downstream / 2 Upstream
  • 15 Downstream / 2 Upstream
  • 30 Downstream / 5 Upstream
** Speeds available in certain markets
  • 5 Downstream / 2 Upstream
  • 10 Downstream / 2 Upstream
  • 15 Downstream / 2 Upstream
  • 20 Downstream / 5 Upstream
  • 30 Downstream / 5 Upstream
  • 50 Downstream / 5 Upstream
  • 50 Downstream / 10 Upstream

Verizon is constructing a passive optical network . Optical fiber extends from central offices to unpowered hub , in which the optical signal is optically split up to 32 ways.
The active components adhere to the ITU-T G.983 standard, also known as APON or BPON, which provides:
  • 622 Mbit/s (77.75 MByte/s) downstream @ 1490 nm
  • 155 Mbit/s (19.375 MByte/s) upstream @ 1310 nm
  • RF video overlay @ 1550 nm
Most of the optical network terminals (ONT) being deployed by Verizon are Tellabs 1600 series ONT. This ONT provides up to four provisionable voice telephone ports, a 10/100 Mb/s Ethernet interface for data traffic, and one coaxial connector for CATV services. The Motorola ONT V1000 is rarely used.
Verizon includes the Actiontec MI424-WR Coax-enabled broadband home wireless-G router now for free with installations. This device is used for both FiOS TV and FiOS internet. Verizon initially used the D-link DI-624 router but has since switched to the Actiontec for the added MoCA capabilities.

You hear about fiber-optic cables whenever people talk about the telephone system, the cable TV system or the Internet. Fiber-optic lines are strands of optically pure glass as thin as a human hair that carry digital information over long distances. They are also used in medical imaging and mechanical engineering inspection.
In this article, we will show you how these tiny strands of glass transmit light and the fascinating way that these strands are made.

What are Fiber Optics?

Fiber optics (optical fibers) are long, thin strands of very pure glass about the diameter of a human hair. They are arranged in bundles called optical cables and used to transmit light signals over long distances.
external image fiber-optic-fiber.jpg
Parts of a single optical fiber
If you look closely at a single optical fiber, you will see that it has the following parts:
  • Core - Thin glass center of the fiber where the light travels
  • Cladding - Outer optical material surrounding the core that reflects the light back into the core
  • Buffer coating - Plastic coating that protects the fiber from damage and moisture
Hundreds or thousands of these optical fibers are arranged in bundles in optical cables. The bundles are protected by the cable's outer covering, called a jacket.
Optical fibers come in two types:
  • Single-mode fibers
  • Multi-mode fibers
See Mode Theory for a good explanation.
Single-mode fibers have small cores (about 3.5 x 10-4 inches or 9 microns in diameter) and transmit infrared laser light (wavelength

1,300 to 1,550 nanometers). Multi-mode fibers have larger cores (about 2.5 x 10-3 inches or 62.5 microns in diameter) and transmit infrared light (wavelength

850 to 1,300 nm) from light-emitting diodes (LEDs).
Some optical fibers can be made from plastic. These fibers have a large core (0.04 inches or 1 mm diameter) and transmit visible red light (wavelength = 650 nm) from LEDs.
Let's look at how an optical fiber works.

How Does an Optical Fiber Transmit Light?

Suppose you want to shine a flashlight beam down a long, straight hallway. Just point the beam straight down the hallway -- light travels in straight lines, so it is no problem. What if the hallway has a bend in it? You could place a mirror at the bend to reflect the light beam around the corner. What if the hallway is very winding with multiple bends? You might line the walls with mirrors and angle the beam so that it bounces from side-to-side all along the hallway. This is exactly what happens in an optical fiber.
external image fiber-optic-transmission.gif
Diagram of total internal reflection in an optical fiber

The light in a fiber-optic cable travels through the core (hallway) by constantly bouncing from the cladding (mirror-lined walls), a principle called total internal reflection. Because the cladding does not absorb any light from the core, the light wave can travel great distances. However, some of the light signal degrades within the fiber, mostly due to impurities in the glass. The extent that the signal degrades depends on the purity of the glass and the wavelength of the transmitted light (for example, 850 nm

60 to 75 percent/km; 1,300 nm

50 to 60 percent/km; 1,550 nm is greater than 50 percent/km). Some premium optical fibers show much less signal degradation -- less than 10 percent/km at 1,550 nm.

A Fiber-Optic Relay System

To understand how optical fibers are used in communications systems, let's look at an example from a World War II movie or documentary where two naval ships in a fleet need to communicate with each other while maintaining radio silence or on stormy seas. One ship pulls up alongside the other. The captain of one ship sends a message to a sailor on deck. The sailor translates the message into Morse code (dots and dashes) and uses a signal light (floodlight with a venetian blind type shutter on it) to send the message to the other ship. A sailor on the deck of the other ship sees the Morse code message, decodes it into English and sends the message up to the captain.
Now, imagine doing this when the ships are on either side of the ocean separated by thousands of miles and you have a fiber-optic communication system in place between the two ships. Fiber-optic relay systems consist of the following:
  • Transmitter - Produces and encodes the light signals
  • Optical fiber - Conducts the light signals over a distance
  • Optical regenerator - May be necessary to boost the light signal (for long distances)
  • Optical receiver - Receives and decodes the light signals
The transmitter is like the sailor on the deck of the sending ship. It receives and directs the optical device to turn the light "on" and "off" in the correct sequence, thereby generating a light signal.
The transmitter is physically close to the optical fiber and may even have a lens to focus the light into the fiber. Lasers have more power than LEDs, but vary more with changes in temperature and are more expensive. The most common wavelengths of light signals are 850 nm, 1,300 nm, and 1,550 nm (infrared, non-visible portions of the spectrum).
Optical Regenerator
As mentioned above, some signal loss occurs when the light is transmitted through the fiber, especially over long distances (more than a half mile, or about 1 km) such as with undersea cables. Therefore, one or more optical regenerators is spliced along the cable to boost the degraded light signals.
An optical regenerator consists of optical fibers with a special coating (doping). The doped portion is "pumped" with a laser. When the degraded signal comes into the doped coating, the energy from the laser allows the doped molecules to become lasers themselves. The doped molecules then emit a new, stronger light signal with the same characteristics as the incoming weak light signal. Basically, the regenerator is a laser amplifier for the incoming signal. See Fiber Amplifiers for more details.
Optical Receiver
The optical receiver is like the sailor on the deck of the receiving ship. It takes the incoming digital light signals, decodes them and sends the electrical signal to the other user's computer, TV or telephone (receiving ship's captain). The receiver uses a photocell or photodiode to detect the light.

Advantages of Fiber Optics

Why are fiber-optic systems revolutionizing telecommunications? Compared to conventional metal wire (copper wire), optical fibers are:
  • Less expensive - Several miles of optical cable can be made cheaper than equivalent lengths of copper wire. This saves your provider (cable TV, Internet) and you money.
  • Thinner - Optical fibers can be drawn to smaller diameters than copper wire.
  • Higher carrying capacity - Because optical fibers are thinner than copper wires, more fibers can be bundled into a given-diameter cable than copper wires. This allows more phone lines to go over the same cable or more channels to come through the cable into your cable TV box.
  • Less signal degradation - The loss of signal in optical fiber is less than in copper wire.
  • Light signals - Unlike electrical signals in copper wires, light signals from one fiber do not interfere with those of other fibers in the same cable. This means clearer phone conversations or TV reception.
  • Low power - Because signals in optical fibers degrade less, lower-power transmitters can be used instead of the high-voltage electrical transmitters needed for copper wires. Again, this saves your provider and you money.
  • Digital signals - Optical fibers are ideally suited for carrying digital information, which is especially useful in computer networks.
  • Non-flammable - Because no electricity is passed through optical fibers, there is no fire hazard.
  • Lightweight - An optical cable weighs less than a comparable copper wire cable. Fiber-optic cables take up less space in the ground.
  • Flexible - Because fiber optics are so flexible and can transmit and receive light, they are used in many flexible digital cameras for the following purposes:
Because of these advantages, you see fiber optics in many industries, most notably telecommunications and computer networks. For example, if you telephone Europe from the United States (or vice versa) and the signal is bounced off a communications satellite, you often hear an echo on the line. But with transatlantic fiber-optic cables, you have a direct connection with no echoes.

How Are Optical Fibers Made?

Now that we know how fiber-optic systems work and why they are useful -- how do they make them? Optical fibers are made of extremely pure optical glass. We think of a glass window as transparent, but the thicker the glass gets, the less transparent it becomes due to impurities in the glass. However, the glass in an optical fiber has far fewer impurities than window-pane glass. One company's description of the quality of glass is as follows: If you were on top of an ocean that is miles of solid core optical fiber glass, you could see the bottom clearly.
Making optical fibers requires the following steps:
  1. Making a preform glass cylinder
  2. Drawing the fibers from the preform
  3. Testing the fibers
Making the Preform Blank
The glass for the preform is made by a process called modified chemical vapor deposition (MCVD).

external image fiber-optic-fibercoreltd-pre-fab1.jpg
Image courtesy Fibercore Ltd.
MCVD process for making the preform blank
In MCVD, oxygen is bubbled through solutions of silicon chloride (SiCl4), germanium chloride (GeCl4) and/or other chemicals. The precise mixture governs the various physical and optical properties (index of refraction, coefficient of expansion, melting point, etc.). The gas vapors are then conducted to the inside of a synthetic silica or quartz tube (cladding) in a special lathe. As the lathe turns, a torch is moved up and down the outside of the tube. The extreme heat from the torch causes two things to happen:

external image fiber-optic-fibercoreltd-lathe2.jpg
Photo courtesy Fibercore Ltd.
Lathe used in preparing
the preform blank

  • The silicon and germanium react with oxygen, forming silicon dioxide (SiO2) and germanium dioxide (GeO2).
  • The silicon dioxide and germanium dioxide deposit on the inside of the tube and fuse together to form glass.
The lathe turns continuously to make an even coating and consistent blank. The purity of the glass is maintained by using corrosion-resistant plastic in the gas delivery system (valve blocks, pipes, seals) and by precisely controlling the flow and composition of the mixture. The process of making the preform blank is highly automated and takes several hours. After the preform blank cools, it is tested for quality control (index of refraction).
Drawing Fibers from the Preform Blank
Once the preform blank has been tested, it gets loaded into a fiber drawing tower.

external image fiber-optic-fibercoreltd-fibrtowr2.jpg
Diagram of a fiber drawing tower used to draw optical glass fibers from a preform blank
The blank gets lowered into a graphite furnace (3,452 to 3,992 degrees Fahrenheit or 1,900 to 2,200 degrees Celsius) and the tip gets melted until a molten glob falls down by gravity. As it drops, it cools and forms a thread.

external image fiber-optic-fibercoreltd-tower.jpg
The operator threads the strand through a series of coating cups (buffer coatings) and ultraviolet light curing ovens onto a tractor-controlled spool. The tractor mechanism slowly pulls the fiber from the heated preform blank and is precisely controlled by using a laser micrometer to measure the diameter of the fiber and feed the information back to the tractor mechanism. Fibers are pulled from the blank at a rate of 33 to 66 ft/s (10 to 20 m/s) and the finished product is wound onto the spool. It is not uncommon for spools to contain more than 1.4 miles (2.2 km) of optical fiber.
Testing the Finished Optical Fiber
external image fiber-optic-corning-spool.jpg
Photo courtesy Corning
Finished spool of optical fiber
The finished optical fiber is tested for the following:
  • Tensile strength - Must withstand 100,000 lb/in2 or more
  • Refractive index profile - Determine numerical aperture as well as screen for optical defects
  • Fiber geometry - Core diameter, cladding dimensions and coating diameter are uniform
  • Attenuation - Determine the extent that light signals of various wavelengths degrade over distance
  • Information carrying capacity (bandwidth) - Number of signals that can be carried at one time (multi-mode fibers)
  • Chromatic dispersion - Spread of various wavelengths of light through the core (important for bandwidth)
  • Operating temperature/humidity range
  • Temperature dependence of attenuation
  • Ability to conduct light underwater - Important for undersea cables
Once the fibers have passed the quality control, they are sold to telephone companies, cable companies and network providers. Many companies are currently replacing their old copper-wire-based systems with new fiber-optic-based systems to improve speed, capacity and clarity.

Physics of Total Internal Reflection

When light passes from a medium with one index of refraction (m1) to another medium with a lower index of refraction (m2), it bends or refracts away from an imaginary line perpendicular to the surface (normal line). As the angle of the beam through m1 becomes greater with respect to the normal line, the refracted light through m2 bends further away from the line.
At one particular angle (critical angle), the refracted light will not go into m2, but instead will travel along the surface between the two media (sine [critical angle] = n2/n1 where n1 and n2 are the indices of refraction [n1 is greater than n2]). If the beam through m1 is greater than the critical angle, then the refracted beam will be reflected entirely back into m1 (total internal reflection), even though m2 may be transparent!
In physics, the critical angle is described with respect to the normal line. In fiber optics, the critical angle is described with respect to the parallel axis running down the middle of the fiber. Therefore, the fiber-optic critical angle = (90 degrees - physics critical angle).

external image fiber-optic-ir.gif
Total internal reflection in an optical fiber
In an optical fiber, the light travels through the core (m1, high index of refraction) by constantly reflecting from the cladding (m2, lower index of refraction) because the angle of the light is always greater than the critical angle. Light reflects from the cladding no matter what angle the fiber itself gets bent at, even if it's a full circle!
Because the cladding does not absorb any light from the core, the light wave can travel great distances. However, some of the light signal degrades within the fiber, mostly due to impurities in the glass. The extent that the signal degrades depends upon the purity of the glass and the wavelength of the transmitted light (for example, 850 nm

60 to 75 percent/km; 1,300 nm

50 to 60 percent/km; 1,550 nm is greater than 50 percent/km). Some premium optical fibers show much less signal degradation -- less than 10 percent/km at 1,550 nm.
For more information on fiber optics and related topics, check out the links on the next page.